Tuesday , October 22 2019

Best Floor Jack Reviews and Comparison

Last Updated on

If you wish to own the highest quality floor jack, the kind that makes working on your car a whole lot easier. You got to be sure that you are buying the precise floor jack you need and we believe the following inside information would be helpful.

All of the knowledge you gather on mechanics, savvy, and expertise are not going to help you at all if you do not have the right tools with you. So that you should make sure that you buy the best floor jack, which gives you opportunity to work comfortably, efficiently, and safely.

Powerzone 380044 – 3 Ton Aluminum and Steel Garage Jack

The Powerzone 380044 floor jack is one of the bestselling jacks in the market. Even though it is a Chinese product, this floor jack is extremely well made giving it nearly 380 5-star ratings. The Powerzone 380044 is made out of steel and aluminum giving you the strength as well as portability. The steel lifting arm provides the strength required to lift vehicles weighting up to 3 tons (6,000 pounds) while the aluminum frame helps to keep the overall weight down. This is one of the few 3 ton floor jacks weighing less than 65 pounds. Even though design is not a low profile one, the 4 inch minimum height is quite decent. Owners of lowered Chevrolet Corvettes claimed that they have no issues with this jack.

The Powerzone 380044 has a great lifting range of 14 1/4 inches, which enables it to lift a vehicle up to 18 1/4″ off the ground. It also boasts a dual-cylinder quick lifting hydraulic system, which gives the benefits of saving both time and effort, when lifting loads. It is equipped with a safety valve to prevent damages from overloading.

The unloaded saddle can lifted to the maximum height of 18 1/4 with only 6 full strokes of the jack handle. The saddle is with a rubber pad preventing the underside of your vehicle from damages that may happen when lifting. The jack handle is a two piece one and the lower piece is covered in thick black foam to prevent damages to your vehicle by accidental contact when pumping. All the wheels are steel made while the front wheels are fixed and the rear wheels are caster-type. The caster type wheels are rotatable 360 degrees making the jack easy to position and roll around. The manufacturer included a handle on each side of the body to make it easy to carry.

Considering the aforesaid factors, the 3 ton capacity Powerzone 380044 floor jack is an excellent tool valued for the money you spend and would be a great addition to any home garage.

SPECIFICATIONS

  • Max Lifting Capacity – 3 tons (6,000 pounds)
  • Min Lift Height – 4”
  • Max Lift Height – 18 ¼”
  • Weight – 59.2 pounds

FEATURES

  • Made with both steel and aluminium
  • Dual Cylinder Quick Lift System
  • Rubber padded saddle
  • Foam covered handle
  • Safety valve to prevent overloading
  • Swiveling rear wheels
  • Handles on both sides for easy carrying

Watch this video, make sure you are buying the right Powerzone 380044 floor jack:

Click For Price and Features

Image Source: Amazon.com

Hein-Werner HW93642 Blue Hydraulic Service Jack – 2 Ton Capacity

With so many floor jack options in the market today, it may be difficult to decide which one you should really buy. To help you make the best decision, here’s a Hein-Werner HW93642 Floor Jack review.

Introduction to Hein-Werner

For every car owner, there is a service jack. You need one in case your tire burstsor you meet a technical problem while on the road. But what are the kinds of car jack you should buy?

A hydraulic floor jack is one of the most common kinds of floor jacks. Many people prefer it because it’s easy to use. What makes a hydraulic floor jack different is its use of hydraulic fluid. Oil is used to lubricate the hydraulic chamber. To operate it, you only need to pull back the plunger.

There are several hydraulic floor jack brands in the market. Among the best is the Hein-Werner. Hein-Werner’s floor jacks are all manufactured in the US. They have a high standard of performance and quality for their products. Thus, they usually manufacture jacks that are not only rugged in design but are also highly dependable.

HW93642 Floor JackHein-Werner has been in the field for quite a while, and they claim to be the favorite for military and private company’s lift applications. They have 2-ton floor jacks, 3-ton floor jacks, and other heavy duty floor jacks. One of their best products is the Hein-Werner HW93642 Floor Jack.

What We Like

  • Made in the USA

Any expert will tell you that the best floor jacks are manufactured in the US. Jacks made in the country are known for their durability and quality, and Hein-Werner is one of the top brands in the country.

Hein-Werner HW93642 Floor Jack will not let you down as it is built to meet the US standards. In other words, it is a quality tool. It performs well, and it looks durable enough to last for years. If you’ve been using inferior floor jacks made from countries other than the US, then you’ll be surprised by how easy it is to use Hein-Werner HW93642 Floor Jack.

  • Precise Hydraulic Valve Control

Hein-Werner HW93642 Floor Jack has a universal joint that allows you to precisely control the hydraulic valve. Because it has a U-Joint release mechanism and a unique in-line pump assembly, using it to lower or lift your car is effortless.

  • Dependable Body Design

Hein-Werner HW93642 Floor Jack is mainly made out of steel. Thus, it is strong enough to handle 2 tons of vehicle. Its body plates are flanged, thus reducing flexes and increasing rigidity. With a minimum lift of 3-3/4 inches, it is not a low jack.

Hein-Werner HW93642 Floor Jack has notches on its sides so that when you operate it, the vehicle does not slip off. The product’s rear casters can swivel up to 360 degrees so you can roll and position it easily.

  • Good Lifting System Design

Like most floor jacks, the product’s hydraulic valve of Hein-Werner HW93642 Floor Jack can be opened and closed by turning the lifting pole in a clockwise and then in a counter-clockwise manner. This said, the single hydraulic piston is sealed. Thus, no dirt or other debris can contaminate the fluid inside.

Because it makes use of a universal joint between the hydraulic valve and the pole socket, you will require little effort to operate the pole and lift or lower a vehicle. What’s more is that it comes with a safety valve, so you can’t forcefully use it to lift loads heavier than 2 tons.

  • Decent Minimum Lift Height

The Hein-Werner HW93642 Floor Jack can lift vehicles of up to 2 tons. It has a minimum lift range of 4-1/2 inches and a maximum lift range of 20-1/4 inches. To improve control, it comes with a U-Joint and a one-piece handle. So, if you need to bend it while working with a vehicle, you can do so easily.

Buy From Amazon

What We Don’t Like

  • At 99 pounds, the Hein-Werner HW93642 Floor Jack is too heavy to carry. To maneuver it easily, Hein-Werner puts large front and rear wheels on it. However, if you must carry it, you need to remove the lifting pole and grip it by the front axle.
  • While the lack of padding on the saddle is not a deal breaker, it certainly is disappointing. The saddle is square-shaped with round corners. Without the padding, you might scratch your vehicle.
  • The Hein-Werner HW93642 Floor Jack only has a one-piece lifting pole. When you use it in a small garage, you might find that it’s hard to maneuver. Working with it in tight spaces will require some thinking as you need to find the right angle to position it.
  • The one-piece lifting pole of Hein-Werner HW93642 Floor Jack is made out of steel. Thus, itcan be rigid. To remove it, you need to loosen a 14mm bolt.
  • The Hein-Werner HW93642 Floor Jack is not a quick-lifting jack. It will take you several strokesbefore you can successfully lift the pole and reach its maximum height.


Tips in Buying a Floor Jack

Whether you’ve decided to buy a Hein-Werner jack or any other jack stand, there are factors that you should consider.

  1. Check whether the floor jack is sturdy enough to lift your vehicle safely and securely.
  2. See whether there are fast pump features and padded handles to make operations easy.
  3. Test how stable the floor jack can lift the vehicle in a specified time.
  4. High cost floor jacks are usually more reliable than cheap ones. Set a budget, but don’t compromise quality.
  5. Check the brand. Brands like Hein-Werner are popular for a reason. They are trustworthy.

Conclusion

In order to know whether this product is really the one you need, you must weigh in its advantages and disadvantages with this Hein-Werner HW93642 Floor Jack review. The floor jack has a good body design, system, hydraulic valve control, and minimum lift height.

However, it does not come with padding and may be difficult to move in tight spaces. Generally, it’s a decent floor jack that’s better than most of those in the market.


Buy From Amazon

Image Source: Amazon.com

Arcan ALJ3T Aluminum Floor Jack – 3 Ton Capacity

LIFTING CAPACITY: 3 tons (6,000 pounds) aluminum jack

WEIGHT: 56 pounds (25.4 kilograms)

LIFTING RANGE: 3 3/4 ″ to 18 1/8″

BODY DESIGN: Do not get distracted by beautiful design. This aluminum jack is no beauty queen. It is a low profile design that allows fitting under any type of vehicle.  It still has a maximum lifting height than or equal to most of its competitors. Even though it is made out of nearly 100% aluminum, it has thick frame, side plates and a reinforced lifting arm that enables it to lift up to 3 tons (6,000 pounds) safely. The lifting pole is a two-piece design made out of aluminum. It snaps together with a quick-lock button press system. Only the bottom half of the lifting pole is padded and the pole tends to flex slightly when been used. Even though the saddle has a soft rubber pad which prevents damages to the underside of your vehicle, it can get torn up easily. The rear casters have ball bearings which allow them to rotate with ease. There are two handles on each side allowing the jack to be easily carried around. Availability of a bypass and an overload valve prevents over-extension of hydraulic ram and using the jack beyond rated capacity. This jack complies with 2009 ASME PALD Standard. aluminum jack

LIFTING AND LOWERING SYSTEM: The lifting system has a dual piston design, which allows relatively quick and effortless lifting. This one is not having a super-fast lifting system. It takes about 12 full stokes to go from fully lower to fully raised. However, the effort required on the lifting pole is much less than most jacks that fully raise in four to five strokes.  The hydraulic release allows the load to be lowered slowly and steadily.

Pros and Cons of ALJ3T 3 Ton Aluminum Floor Jack

PROS

  • Beautiful design
  • Low profile design but better lifting height
  • Strong, but relatively light due to aluminum construction
  • Very controlled lowering of the load
  • 2-piece quick-lock lifting pole for easy storage
  • Carrying handles on both sides

CONS

  • Made in China
  • Rubber saddle pad easily torn up the aluminum jack

3 Ton Aluminum Floor Jack

Click For Price and Features

Image Source: Amazon.com

Check Also

Strongway Hydraulic Bottle Jack

Top 5 Strongway Hydraulic Bottle Jack Reviews

Last Updated on 1 month ago If you are related to any field where lifting …

×